Operational amplifier as a comparator at high frequencyReasons not to use a 741 op-amp?Can I use LM324 as a Schmitt trigger?Simple op-amp differential amplifierOp amp has a biased outputReduced output of op amp peak detection and hold circuitHow to select the right Operational Amplifier as an impedance converter?Bias voltage of non-inverting op amplifier drops to 0 when input signal connectedHigh negative voltages with op-ampopamp output unstableComparator circuit undesirable fluctuations20kHz sine wave signal amplificationIf there exists a cascade of op amps, does the previous op amp's slew rate affect the later op amp's slew rates?
Perform and show arithmetic with LuaLaTeX
How much RAM could one put in a typical 80386 setup?
How to determine what difficulty is right for the game?
Can I ask the recruiters in my resume to put the reason why I am rejected?
Convert two switches to a dual stack, and add outlet - possible here?
Malformed Address '10.10.21.08/24', must be X.X.X.X/NN or
Maximum likelihood parameters deviate from posterior distributions
tikz convert color string to hex value
meaning of に in 本当に?
What would happen to a modern skyscraper if it rains micro blackholes?
I'm flying to France today and my passport expires in less than 2 months
NMaximize is not converging to a solution
Why are electrically insulating heatsinks so rare? Is it just cost?
What does the "remote control" for a QF-4 look like?
When a company launches a new product do they "come out" with a new product or do they "come up" with a new product?
Why do I get two different answers for this counting problem?
What does "Puller Prush Person" mean?
Why does Kotter return in Welcome Back Kotter?
Codimension of non-flat locus
"You are your self first supporter", a more proper way to say it
Why can't we play rap on piano?
Intersection point of 2 lines defined by 2 points each
Why is consensus so controversial in Britain?
Do infinite dimensional systems make sense?
Operational amplifier as a comparator at high frequency
Reasons not to use a 741 op-amp?Can I use LM324 as a Schmitt trigger?Simple op-amp differential amplifierOp amp has a biased outputReduced output of op amp peak detection and hold circuitHow to select the right Operational Amplifier as an impedance converter?Bias voltage of non-inverting op amplifier drops to 0 when input signal connectedHigh negative voltages with op-ampopamp output unstableComparator circuit undesirable fluctuations20kHz sine wave signal amplificationIf there exists a cascade of op amps, does the previous op amp's slew rate affect the later op amp's slew rates?
.everyoneloves__top-leaderboard:empty,.everyoneloves__mid-leaderboard:empty,.everyoneloves__bot-mid-leaderboard:empty margin-bottom:0;
$begingroup$
I am trying to generate a sinusoidal PWM signal using analog circuits.
I want to compare my sine wave and triangular wave using an operational amplifier (LM741) which has a rise time of 0.3 µs and slew rate 0.5 V/µs, which will good at 5 kHz theoretically. But I am not getting a good PWM output.
So I first tried to compare the sine wave with a reference voltage (2.2 volt). Sine wave amplitude = 2.5 volt (5 V peak to peak) and frequency 100 Hz and 5 kHz.
- At low frequency (say 100 Hz), the output is good
- At high frequency (say 5 kHz), the output is too bad.
What will be the problem...
If the response is the problem of the comparator, but the slew rate is 0.5 V/µs.
Calculation of slew rate for a sinusoidal signal...
Slew rate= Vm * 2pi * Frequency
= 5 V * 2pi* 5000 Hz
= 1570796 volt per second or 0.15 V/µs
Theoretically the slew rate of 0.5 V/µs will be OK for a sinusoidal signal of 5 kHz and 5 volt peak to peak. But in my case the signal is distorted.
Where am I wrong?
operational-amplifier comparator
edited 7 hours ago
Peter Mortensen
1,60031422
asked 16 hours ago
NihalNihal
517
$endgroup$
|
show 2 more comments
$begingroup$
I am trying to generate a sinusoidal PWM signal using analog circuits.
I want to compare my sine wave and triangular wave using an operational amplifier (LM741) which has a rise time of 0.3 µs and slew rate 0.5 V/µs, which will good at 5 kHz theoretically. But I am not getting a good PWM output.
So I first tried to compare the sine wave with a reference voltage (2.2 volt). Sine wave amplitude = 2.5 volt (5 V peak to peak) and frequency 100 Hz and 5 kHz.
- At low frequency (say 100 Hz), the output is good
- At high frequency (say 5 kHz), the output is too bad.
What will be the problem...
If the response is the problem of the comparator, but the slew rate is 0.5 V/µs.
Calculation of slew rate for a sinusoidal signal...
Slew rate= Vm * 2pi * Frequency
= 5 V * 2pi* 5000 Hz
= 1570796 volt per second or 0.15 V/µs
Theoretically the slew rate of 0.5 V/µs will be OK for a sinusoidal signal of 5 kHz and 5 volt peak to peak. But in my case the signal is distorted.
Where am I wrong?
operational-amplifier comparator
edited 7 hours ago
Peter Mortensen
1,60031422
asked 16 hours ago
NihalNihal
517
$endgroup$
$begingroup$
It looks like there's a significant lag/delay in the output's response w.r.t. the input signal (~30µs?). What may be causing this? What's connected to the output? 'Scope probe only?
$endgroup$
– JimmyB
16 hours ago
5
$begingroup$
Why you shouldn't use the 741.
$endgroup$
– JRE
15 hours ago
$begingroup$
For 5Khz i thought 741 will be ok, for what i calculated .Orelse sure i will change the opp amp which having high slew rate and i will update it.......@JRE
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
You're latching up.
$endgroup$
– Scott Seidman
14 hours ago
1
$begingroup$
Note that this question is about the theory behind the calculations. Telling OP to change his OP-amp does nothing to answer the question. It just solves the problem without OP knowing why.
$endgroup$
– pipe
7 hours ago
|
show 2 more comments
$begingroup$
I am trying to generate a sinusoidal PWM signal using analog circuits.
I want to compare my sine wave and triangular wave using an operational amplifier (LM741) which has a rise time of 0.3 µs and slew rate 0.5 V/µs, which will good at 5 kHz theoretically. But I am not getting a good PWM output.
So I first tried to compare the sine wave with a reference voltage (2.2 volt). Sine wave amplitude = 2.5 volt (5 V peak to peak) and frequency 100 Hz and 5 kHz.
- At low frequency (say 100 Hz), the output is good
- At high frequency (say 5 kHz), the output is too bad.
What will be the problem...
If the response is the problem of the comparator, but the slew rate is 0.5 V/µs.
Calculation of slew rate for a sinusoidal signal...
Slew rate= Vm * 2pi * Frequency
= 5 V * 2pi* 5000 Hz
= 1570796 volt per second or 0.15 V/µs
Theoretically the slew rate of 0.5 V/µs will be OK for a sinusoidal signal of 5 kHz and 5 volt peak to peak. But in my case the signal is distorted.
Where am I wrong?
operational-amplifier comparator
edited 7 hours ago
Peter Mortensen
1,60031422
asked 16 hours ago
NihalNihal
517
$endgroup$
I am trying to generate a sinusoidal PWM signal using analog circuits.
I want to compare my sine wave and triangular wave using an operational amplifier (LM741) which has a rise time of 0.3 µs and slew rate 0.5 V/µs, which will good at 5 kHz theoretically. But I am not getting a good PWM output.
So I first tried to compare the sine wave with a reference voltage (2.2 volt). Sine wave amplitude = 2.5 volt (5 V peak to peak) and frequency 100 Hz and 5 kHz.
- At low frequency (say 100 Hz), the output is good
- At high frequency (say 5 kHz), the output is too bad.
What will be the problem...
If the response is the problem of the comparator, but the slew rate is 0.5 V/µs.
Calculation of slew rate for a sinusoidal signal...
Slew rate= Vm * 2pi * Frequency
= 5 V * 2pi* 5000 Hz
= 1570796 volt per second or 0.15 V/µs
Theoretically the slew rate of 0.5 V/µs will be OK for a sinusoidal signal of 5 kHz and 5 volt peak to peak. But in my case the signal is distorted.
Where am I wrong?
operational-amplifier comparator
operational-amplifier comparator
edited 7 hours ago
Peter Mortensen
1,60031422
asked 16 hours ago
NihalNihal
517
edited 7 hours ago
Peter Mortensen
1,60031422
asked 16 hours ago
NihalNihal
517
edited 7 hours ago
Peter Mortensen
1,60031422
edited 7 hours ago
Peter Mortensen
1,60031422
edited 7 hours ago
Peter Mortensen
1,60031422
1,60031422
asked 16 hours ago
NihalNihal
517
asked 16 hours ago
NihalNihal
517
asked 16 hours ago
NihalNihal
517
517
$begingroup$
It looks like there's a significant lag/delay in the output's response w.r.t. the input signal (~30µs?). What may be causing this? What's connected to the output? 'Scope probe only?
$endgroup$
– JimmyB
16 hours ago
5
$begingroup$
Why you shouldn't use the 741.
$endgroup$
– JRE
15 hours ago
$begingroup$
For 5Khz i thought 741 will be ok, for what i calculated .Orelse sure i will change the opp amp which having high slew rate and i will update it.......@JRE
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
You're latching up.
$endgroup$
– Scott Seidman
14 hours ago
1
$begingroup$
Note that this question is about the theory behind the calculations. Telling OP to change his OP-amp does nothing to answer the question. It just solves the problem without OP knowing why.
$endgroup$
– pipe
7 hours ago
|
show 2 more comments
$begingroup$
It looks like there's a significant lag/delay in the output's response w.r.t. the input signal (~30µs?). What may be causing this? What's connected to the output? 'Scope probe only?
$endgroup$
– JimmyB
16 hours ago
5
$begingroup$
Why you shouldn't use the 741.
$endgroup$
– JRE
15 hours ago
$begingroup$
For 5Khz i thought 741 will be ok, for what i calculated .Orelse sure i will change the opp amp which having high slew rate and i will update it.......@JRE
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
You're latching up.
$endgroup$
– Scott Seidman
14 hours ago
1
$begingroup$
Note that this question is about the theory behind the calculations. Telling OP to change his OP-amp does nothing to answer the question. It just solves the problem without OP knowing why.
$endgroup$
– pipe
7 hours ago
$begingroup$
It looks like there's a significant lag/delay in the output's response w.r.t. the input signal (~30µs?). What may be causing this? What's connected to the output? 'Scope probe only?
$endgroup$
– JimmyB
16 hours ago
$begingroup$
It looks like there's a significant lag/delay in the output's response w.r.t. the input signal (~30µs?). What may be causing this? What's connected to the output? 'Scope probe only?
$endgroup$
– JimmyB
16 hours ago
5
5
$begingroup$
Why you shouldn't use the 741.
$endgroup$
– JRE
15 hours ago
$begingroup$
Why you shouldn't use the 741.
$endgroup$
– JRE
15 hours ago
$begingroup$
For 5Khz i thought 741 will be ok, for what i calculated .Orelse sure i will change the opp amp which having high slew rate and i will update it.......@JRE
$endgroup$
– Nihal
15 hours ago
$begingroup$
For 5Khz i thought 741 will be ok, for what i calculated .Orelse sure i will change the opp amp which having high slew rate and i will update it.......@JRE
$endgroup$
– Nihal
15 hours ago
1
1
$begingroup$
You're latching up.
$endgroup$
– Scott Seidman
14 hours ago
$begingroup$
You're latching up.
$endgroup$
– Scott Seidman
14 hours ago
1
1
$begingroup$
Note that this question is about the theory behind the calculations. Telling OP to change his OP-amp does nothing to answer the question. It just solves the problem without OP knowing why.
$endgroup$
– pipe
7 hours ago
$begingroup$
Note that this question is about the theory behind the calculations. Telling OP to change his OP-amp does nothing to answer the question. It just solves the problem without OP knowing why.
$endgroup$
– pipe
7 hours ago
|
show 2 more comments
5 Answers
5
active
oldest
votes
$begingroup$
The recommendations for you are very simple.
Use a comparator for this application instead of an opamp.
Select a newer part that operates with orders of magnitude faster response time.
It would be the very best thing if the 741 could be eradicated from face of the earth.
Here is what can be achieved with the venerable LM393 at 5kHz. The shown circuit will work even up to about 50kHz before the delay of the LM393 starts to distort the PWM duty cycle.
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
$endgroup$
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
1
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
2
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
|
show 6 more comments
$begingroup$
Opamps work slowly with low power supply voltages. In addition they are designed to work in linear region. As saturated, like in your application, the response has an unpredictable dead time. before the internal saturation is vanished.
I can only repeat what's already said: Get a comparator. 741 was a remarkable step forward half a century ago, but things have developed better since those days.
answered 16 hours ago
user287001user287001
9,6541517
$endgroup$
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
2
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
add a comment |
$begingroup$
Op-amps are susceptible to latch-up. Recovering from saturation at the rails is not an automatic thing. The ratings you are reading a for the op amp working in a feedback mode, not an open loop mode. You would need to find an op amp designed to minimize latch-up, or better yet, when you need a comparator, buy a comparator.
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
$endgroup$
1
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
You may try this, if you want a discrete solution
simulate this circuit – Schematic created using CircuitLab
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
$endgroup$
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
Most garden variety op-amps have internal compensation in the form of a chip capacitor.
This makes them very slow, but more stable in analog circuits.
Why not use a cheap comparator like LM393?
edited 12 hours ago
Renan
4,32222244
answered 16 hours ago
AutisticAutistic
7,49921633
$endgroup$
add a comment |
Your Answer
StackExchange.ifUsing("editor", function ()
return StackExchange.using("mathjaxEditing", function ()
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix)
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
);
);
, "mathjax-editing");
StackExchange.ifUsing("editor", function ()
return StackExchange.using("schematics", function ()
StackExchange.schematics.init();
);
, "cicuitlab");
StackExchange.ready(function()
var channelOptions =
tags: "".split(" "),
id: "135"
;
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function()
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled)
StackExchange.using("snippets", function()
createEditor();
);
else
createEditor();
);
function createEditor()
StackExchange.prepareEditor(
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader:
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
,
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
);
);
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f430885%2foperational-amplifier-as-a-comparator-at-high-frequency%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
5 Answers
5
active
oldest
votes
5 Answers
5
active
oldest
votes
active
oldest
votes
active
oldest
votes
$begingroup$
The recommendations for you are very simple.
Use a comparator for this application instead of an opamp.
Select a newer part that operates with orders of magnitude faster response time.
It would be the very best thing if the 741 could be eradicated from face of the earth.
Here is what can be achieved with the venerable LM393 at 5kHz. The shown circuit will work even up to about 50kHz before the delay of the LM393 starts to distort the PWM duty cycle.
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
$endgroup$
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
1
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
2
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
|
show 6 more comments
$begingroup$
The recommendations for you are very simple.
Use a comparator for this application instead of an opamp.
Select a newer part that operates with orders of magnitude faster response time.
It would be the very best thing if the 741 could be eradicated from face of the earth.
Here is what can be achieved with the venerable LM393 at 5kHz. The shown circuit will work even up to about 50kHz before the delay of the LM393 starts to distort the PWM duty cycle.
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
$endgroup$
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
1
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
2
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
|
show 6 more comments
$begingroup$
The recommendations for you are very simple.
Use a comparator for this application instead of an opamp.
Select a newer part that operates with orders of magnitude faster response time.
It would be the very best thing if the 741 could be eradicated from face of the earth.
Here is what can be achieved with the venerable LM393 at 5kHz. The shown circuit will work even up to about 50kHz before the delay of the LM393 starts to distort the PWM duty cycle.
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
$endgroup$
The recommendations for you are very simple.
Use a comparator for this application instead of an opamp.
Select a newer part that operates with orders of magnitude faster response time.
It would be the very best thing if the 741 could be eradicated from face of the earth.
Here is what can be achieved with the venerable LM393 at 5kHz. The shown circuit will work even up to about 50kHz before the delay of the LM393 starts to distort the PWM duty cycle.
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
edited 15 hours ago
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
answered 16 hours ago
Michael KarasMichael Karas
45.2k348105
45.2k348105
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
1
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
2
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
|
show 6 more comments
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
1
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
2
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
$begingroup$
Sure friend i will change the opp amp or by using comparator, i will update the data soon.
$endgroup$
– Nihal
15 hours ago
1
1
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
$begingroup$
@Nihal - If you show some new results in the question do not delete your original material, Instead add it as an update at the end. The reason for this is that hopefully this question can be a reference to future readers that are looking for information as being discussed here. If you delete the original material the answers here would no longer make much sense to a future reader.
$endgroup$
– Michael Karas
15 hours ago
1
1
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
$begingroup$
"It would be the very best thing if the 741 could be eradicated from face of the earth." ok - I'll bite. what's your reasons?
$endgroup$
– UKMonkey
11 hours ago
2
2
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
@UKMonkey the 741 was first released in 1968. And while it was a fantastic IC at the time, there are vastly superior op-amps available with lower input offset voltage, higher bandwidth, higher input impedance, etc. Most people lean the "ideal op-amp" first, and then immediately jump to one of the most non-ideal op-amps in practice, and wonder why their design doesn't work.
$endgroup$
– CurtisHx
11 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
$begingroup$
LM741 might still be in the textbooks...
$endgroup$
– Peter Mortensen
10 hours ago
|
show 6 more comments
$begingroup$
Opamps work slowly with low power supply voltages. In addition they are designed to work in linear region. As saturated, like in your application, the response has an unpredictable dead time. before the internal saturation is vanished.
I can only repeat what's already said: Get a comparator. 741 was a remarkable step forward half a century ago, but things have developed better since those days.
answered 16 hours ago
user287001user287001
9,6541517
$endgroup$
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
2
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
add a comment |
$begingroup$
Opamps work slowly with low power supply voltages. In addition they are designed to work in linear region. As saturated, like in your application, the response has an unpredictable dead time. before the internal saturation is vanished.
I can only repeat what's already said: Get a comparator. 741 was a remarkable step forward half a century ago, but things have developed better since those days.
answered 16 hours ago
user287001user287001
9,6541517
$endgroup$
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
2
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
add a comment |
$begingroup$
Opamps work slowly with low power supply voltages. In addition they are designed to work in linear region. As saturated, like in your application, the response has an unpredictable dead time. before the internal saturation is vanished.
I can only repeat what's already said: Get a comparator. 741 was a remarkable step forward half a century ago, but things have developed better since those days.
answered 16 hours ago
user287001user287001
9,6541517
$endgroup$
Opamps work slowly with low power supply voltages. In addition they are designed to work in linear region. As saturated, like in your application, the response has an unpredictable dead time. before the internal saturation is vanished.
I can only repeat what's already said: Get a comparator. 741 was a remarkable step forward half a century ago, but things have developed better since those days.
answered 16 hours ago
user287001user287001
9,6541517
answered 16 hours ago
user287001user287001
9,6541517
answered 16 hours ago
user287001user287001
9,6541517
answered 16 hours ago
user287001user287001
9,6541517
9,6541517
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
2
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
add a comment |
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
2
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
$begingroup$
Thank you for your response friend, i will update it after changing the opp amp.
$endgroup$
– Nihal
15 hours ago
2
2
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
@Nihal Comparators have other precautions. They are high speed circuits like logic parts. You must have acceptably short wires and coupling capacitors between supply voltage inputs. Making the circuit with 0,5 meter long wires onto a breadboard without coupling caps (I have seen those attempts) will be useless.
$endgroup$
– user287001
15 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
$begingroup$
Ok friend I will even buy a comparator and I will check with it.
$endgroup$
– Nihal
8 hours ago
add a comment |
$begingroup$
Op-amps are susceptible to latch-up. Recovering from saturation at the rails is not an automatic thing. The ratings you are reading a for the op amp working in a feedback mode, not an open loop mode. You would need to find an op amp designed to minimize latch-up, or better yet, when you need a comparator, buy a comparator.
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
$endgroup$
1
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
Op-amps are susceptible to latch-up. Recovering from saturation at the rails is not an automatic thing. The ratings you are reading a for the op amp working in a feedback mode, not an open loop mode. You would need to find an op amp designed to minimize latch-up, or better yet, when you need a comparator, buy a comparator.
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
$endgroup$
1
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
Op-amps are susceptible to latch-up. Recovering from saturation at the rails is not an automatic thing. The ratings you are reading a for the op amp working in a feedback mode, not an open loop mode. You would need to find an op amp designed to minimize latch-up, or better yet, when you need a comparator, buy a comparator.
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
$endgroup$
Op-amps are susceptible to latch-up. Recovering from saturation at the rails is not an automatic thing. The ratings you are reading a for the op amp working in a feedback mode, not an open loop mode. You would need to find an op amp designed to minimize latch-up, or better yet, when you need a comparator, buy a comparator.
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
answered 14 hours ago
Scott SeidmanScott Seidman
22.7k43286
22.7k43286
1
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
1
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
1
1
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
$begingroup$
Yes, and/or phase inversion, depending on the op-amp type.
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
You may try this, if you want a discrete solution
simulate this circuit – Schematic created using CircuitLab
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
$endgroup$
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
You may try this, if you want a discrete solution
simulate this circuit – Schematic created using CircuitLab
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
$endgroup$
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
You may try this, if you want a discrete solution
simulate this circuit – Schematic created using CircuitLab
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
$endgroup$
You may try this, if you want a discrete solution
simulate this circuit – Schematic created using CircuitLab
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
answered 11 hours ago
analogsystemsrfanalogsystemsrf
16k2822
16k2822
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
$begingroup$
What is it? A Schmitt trigger?
$endgroup$
– Peter Mortensen
10 hours ago
add a comment |
$begingroup$
Most garden variety op-amps have internal compensation in the form of a chip capacitor.
This makes them very slow, but more stable in analog circuits.
Why not use a cheap comparator like LM393?
edited 12 hours ago
Renan
4,32222244
answered 16 hours ago
AutisticAutistic
7,49921633
$endgroup$
add a comment |
$begingroup$
Most garden variety op-amps have internal compensation in the form of a chip capacitor.
This makes them very slow, but more stable in analog circuits.
Why not use a cheap comparator like LM393?
edited 12 hours ago
Renan
4,32222244
answered 16 hours ago
AutisticAutistic
7,49921633
$endgroup$
add a comment |
$begingroup$
Most garden variety op-amps have internal compensation in the form of a chip capacitor.
This makes them very slow, but more stable in analog circuits.
Why not use a cheap comparator like LM393?
edited 12 hours ago
Renan
4,32222244
answered 16 hours ago
AutisticAutistic
7,49921633
$endgroup$
Most garden variety op-amps have internal compensation in the form of a chip capacitor.
This makes them very slow, but more stable in analog circuits.
Why not use a cheap comparator like LM393?
edited 12 hours ago
Renan
4,32222244
answered 16 hours ago
AutisticAutistic
7,49921633
edited 12 hours ago
Renan
4,32222244
edited 12 hours ago
Renan
4,32222244
edited 12 hours ago
Renan
4,32222244
4,32222244
answered 16 hours ago
AutisticAutistic
7,49921633
answered 16 hours ago
AutisticAutistic
7,49921633
answered 16 hours ago
AutisticAutistic
7,49921633
7,49921633
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function ()
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f430885%2foperational-amplifier-as-a-comparator-at-high-frequency%23new-answer', 'question_page');
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function ()
StackExchange.helpers.onClickDraftSave('#login-link');
);
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
$begingroup$
It looks like there's a significant lag/delay in the output's response w.r.t. the input signal (~30µs?). What may be causing this? What's connected to the output? 'Scope probe only?
$endgroup$
– JimmyB
16 hours ago
5
$begingroup$
Why you shouldn't use the 741.
$endgroup$
– JRE
15 hours ago
$begingroup$
For 5Khz i thought 741 will be ok, for what i calculated .Orelse sure i will change the opp amp which having high slew rate and i will update it.......@JRE
$endgroup$
– Nihal
15 hours ago
1
$begingroup$
You're latching up.
$endgroup$
– Scott Seidman
14 hours ago
1
$begingroup$
Note that this question is about the theory behind the calculations. Telling OP to change his OP-amp does nothing to answer the question. It just solves the problem without OP knowing why.
$endgroup$
– pipe
7 hours ago